Shop

100 AH AGM Thumper REDBACK Battery

The technology of the Thumper battery packs has now extended to a Battery! The high quality AGM SLA battery is a true deep cycle battery. But is also available as a hybrid type with both deep cycle and high cranking with 920 CCA.

REG-12V 20Amp Solar Charger with LCD Display

Protect your valuable solar installation & maximise battery service life with our photovoltaic(PV)charge controller. This charger efficiently charges a vast selection of batteries from a wide range of solar panels.

REG-30Amp Solar charging Controller

SPECIFICATIONS

You make a substantial investment in a solar power setup, so make sure you look after your expensive batteries. With a charge controller, you have total control over battery charging and power usage. The LCD shows the system status and LED's at a glance showing the batteries charge status.

    * User-adjustable charging voltages
    * Suitable for wet or sealed lead-acid, lead calcium, lead antimony, Ni-Cd or Nife batteries
    * Pulse Width Modulation for optimum charging
    * 3-Stage, bulk, absorption, and float charge modes with status on LCD
    * Amp-hour input logging readouts in 3 sets, today and last 2 days
    * 5 state - LED indications of battery levels
    * Electronic overcharge protection and back current blocking to panel
    * Dusk to Dawn automatic on/off with 10 slectable on-off programs
    * Adjustable battery low voltage level disconnect and reconnect for DC output
    * Real time clock
    * System status display - Charge current / battery voltage and capacity
    * Overload and shirt circuit protection
    * Over voltage and reverse polarity protection

Dimension: 150mm W x 85mm D x 45mm H

190w Mono-crystalline panel suitable for grid connect

70 a/h AGM Battery

SPECIFICATIONS

CAPACITY: 75 a/h

BATTERY TYPE: Absorbed Glass Mat

DIMENSION: 258 LENGTH x 168 WIDTH x 208 H

WEIGHT: 24 KG

SB 1700 SUNNY BOY INVERTER

Product Specifications
Recc. Maximum PV-power (PPV) approx. 2.050 Wp
Max. DC power (PDC,max) 1,850 W
Max. DC voltage (UDC,max) 400 V
PV-voltage range,MPPT (UPV)139 V – 400 V
Max. input current (IPV,max) 12.6A
DC voltage ripple (Upp) < 10 %
Max .number of strings (parallel)2
DC disconnection Snap cable connectors
Thermally monitored varistors yes
Ground fault monitoring yes
Reverse polarity protection Short circuit diode
Max. AC power (PAC,max)1,700 W
Nominal AC power (PAC,nom) 1,550 W
THD of grid current < 4%
Default range of AC voltage (UAC)198 V – 260 V
Possible range of AC voltage180 V – 265 V
AC frequency (fAC) 49.8 Hz – 50.2
Possible range of AC frequency 45.5 Hz – 54.5 Hz
Phase shift (cos phi) 1
Short circuit proof yes,current control
Connection to utility AC Plug
Max. Efficiency 93.5 %
Euro-efficiency 91.8 %
Enclosure accord.To DIN EN 60529 IP65
Mechanical data ( Width/height/depth in mm) 434/295/212
Weight approx.25 kg

SB2500 SUNNY BOY INVERTER

Product Specifications:
•Recc. Maximum PV-power (PPV) approx. 3,000 Wp
•Max. DC power (PDC,max)2,700 W
•Max. DC voltage (UDC,max) 600 V
•PV-voltage range,MPPT (UPV) 224 V – 400 V
•Max. input current (IPV,max)12 A
•DC voltage ripple (Upp) < 10 %
•Max .number of strings (parallel)3
•DC disconnection Snap cable connectors
•Thermally monitored varistors yes
•Ground fault monitoring yes
•Reverse polarity protection Short circuit diode
•Max. AC power (PAC,max) 2,500 W
•Nominal AC power (PAC,nom) 2,300 W
•THD of grid current < 4%
•Default range of AC voltage (UAC) 198 V – 260 V
•Possible range of AC voltage 180 V – 265 V
•AC frequency (fAC) 49.8 Hz – 50.2
•Possible range of AC frequency 45.5 Hz – 54.5 Hz
•Phase shift (cos phi) 1
•Short circuit proof yes,current control
•Connection to utility AC Plug
•Max. Efficiency 94
•Euro-efficiency 93
•Enclosure accord.To DIN EN 60529 IP65
•Mechanical data ( Width/height/depth in mm) 434/295/214
•Weight approx. 30kg

10 year product warranty
25 years “straight-line” performance guarantee
Made in Korea
Highest quality performance
Premuim 6 inch cells

Dimensions: 1675 x 1000 x 34 mm

5 kw of Amorpous panels (45 panels x 110watts) with Xantrex GT5 Inverter. Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland). If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

1.14 kw of Mono panels (6 of EC Solar 190 watts) with Sun Teams 1500 Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

4 kw of Mono panels, 16 panels x 250 watt, with Xantrex GT 5 Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

For the month of January we are offering no interest  (pay no interest ever) on balance.

25% Deposit now   ($2775)
Loan amount due at install and paid in installments as contracted
Loan Balance $8325
Total price is $11100

Quick and easy
Fast and easy approvals
Simple and easy paperwork

Conditions apply.

1.61 kw of Mono panels (7 Premium Korean panels x 230watts) with 1.7 kw Sunny Boy Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

2.3 kw of Mono panels (10 Premium panels x 230watts) with Xantrex GT28 Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

3 kw of Mono panels, 12 panels x 250watt, with Sunny Boy 3000HF Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

5 kw of Mono panels (20 panels x 250watts) with Xantrex GT5 Inverter.Price is installed on an iron roof that is single story and is within 100 km of an Australian Capital city(mainland).If you have a tiled roof there is a bracket kit required that cost $200. If the house/factory is higher than single story or you are further that 100 km please email us and we will give you a cost on the extra. Please give postcode detail in email and site address.

12v 61 LED work lamp 126mm Diameter plastic ABS body fully waterproof with stainless steel fittings and 400mm wire

91 LED WORK LAMP

12v 84 LED Surface mount interior lamp with rocker switch, strong aluminium body and very nice slim design with defused lens to give a wide viewing angle, L260 x W39.5 x H21mm, current draw 0.37amp @ 13.8v, 1pc/blister pack.

12V 20 White 50 Degree LED Work Lamp With Plastic ABS Body

ZANTREX 2800 INVERTER

Flexible module selection and sizing due to wide PV input MPPT tracking voltage range
Lightweight and versatile mounting bracket
Easy access DC (photovoltaic) and AC (utility) terminal block simplifies wiring
Rugged NEMA 3R inverter enclosure allows reliable indoor and outdoor installations
Performance
Best-in-class efficiency to maximize solar system return on investment
Accurate MPPT tracking ensures maximum energy harvest under any conditions
FCC Part B compliance provides less external electronic interference
Serviceability
10-year standard warranty
Sealed inverter enclosure can be quickly separated from the wiring box